- Air Sampling Pumps
- Calibration Equipment
- Servicing and Calibration
- Sampling Heads
- Sorbent Tubes
- Passive Samplers
- Particulate Monitors
- Filters and Cassettes
- Gas Sample Bags
- Air Sampling Kits
- Gastec Detection Tubes
- Face Level Sampling
- Surface & Skin Sampling
- Asbestos Sampling
- Bioaerosol Sampling
- Environmental Sampling
- Heat Stress Monitor
- Noise Monitoring
- Vibration Monitoring
Button Sampler
The Button Sampler is ideal for low level personal or area inhalable sampling. It is a filter sampler with a porous curved-surface inlet designed to improve the collection characteristics of inhalable dust (100 µm aerodynamic diameter), including bioaerosols for total (viable plus non-viable) microbial count. Its conductive stainless steel inlet reduces electrostatic effects. The evenly spaced holes act as sampling orifices for multi-directional sampling. The proximity of the filter to the inlet minimises transmission losses and provides for equal distribution of particle loading and low intersample variation. The Button Sampler uses 25 mm filters, and filters with pore sizes greater than 1 µm are recommended to lower back pressure and to enhance sample times with personal sample pumps.
- Referenced in MDHS 14/4
- Small and lightweight
- Autoclavable
- Low sensitivity to wind direction and velocity
- Suitable for collecting bioaerosols for viable and non-viable analysis
- 4 L/min flow rate enhances sensitivity
Flow Rate | 4 L/min * | |
Sampling Inlet | Conductive Stainless Steel | |
Body | Aluminium | |
Support Screen | Stainless Steel | |
Clip | Stainless Steel and nylon | |
O-rings | PTFE (inlet) and BUNA-N (body) | |
Filters | 25 mm ** † | |
Inhalable Dust Analysis |
Gravimetric | |
Fungal Spore Analysis |
Epifluorescence microscopy, immunoassay, or polymerase chain reaction (PCR) | |
Metals Analysis | X-ray Fluorescence (XRF) | |
Tubing | 1/4 inch (6.25mm) ID |
* The Button Sampler closely follows the ISO 7708/CEN inhalability curve at 4 L/min. This provides optimum sampling.
** A filter pore size of 1.0 µm or larger is recommended for use with the Button Sampler to reduce back pressure.
† Using Gelatin Filters in the Button Sampler:
For maximum micro-organism survivability and superior collection of inhalable-size bioaerosols, use sterile gelatin filters (225-9551) with the SKC Button Sampler. Combining the Button Sampler with the nurturing properties of gelatin filters creates a sampler that is most efficient at collecting inhalable bioaerosols for viable or non-viable analysis.
Description | Pack Size | Part Number | |
Button Sampler with lapel clip; requires a 25 mm diameter filter | Each | 225-360 |
Description | Pack Size | Part Number | |
Protective Shield, for abrasive blasting environments | Each | 225-366 | |
Button Sampler Calibration Adaptor | Each | 225-361 | |
Filter Transport Case, for 25 mm diameter filters, conductive plastic | 10 | 225-67-10 | |
Replacement O-ring PTFE, for Button Sampler | Each | P32265 | |
Replacement O-ring BUNA-N, for Button Sampler | 50 | P31891 | |
Glass Fibre filters, diameter 25 mm, 1.0 µm Liquid nominal pore size | 500 | 225-702 | |
Mixed Cellulose Ester filters (MCE), diameter 25 mm, pore size 1.2 µm | 100 | 225-1912 | |
PTFE filters with PMP support (Teflo®) # ‡ diameter 25 mm, pore size 3 µm | 50 | 225-1711 | |
Gelatin filters, sterilised, diameter 25 mm † | 50 | 225-9551 | |
Polyvinyl chloride filters (PVC), diameter 25 mm, pore size 5.0 µm | 100 | 225-5-25 | |
Support Screen for Button Sampler, 25 mm diameter | Each | P26034 |
‡ Back pressure on PTFE filters can vary within the same lot
† Gelatin filters dissolve when placed on agar
# Maximum operating temperature is 240°C (464°F)